CDI-D100

前言前言感谢您选用德力西（杭州）变频器有限公司生产的CDI-D100系列通用变频器。在使用CDI-D100系列通用变频器之前,请您仔细阅读本手册，以保证正确使用。不正确的使用可能会造成变频器运行不正常、发生故障或降低使用寿命，乃至发生人身伤害事故。因此使用前应认真阅读本说明书，严格按说明使用。本手册为标准附件，务必请您阅读后妥善保管，以备今后对变频器进行检修和维护时使用。本手册除叙述操作说明外，还提供接线图供您参考。如果您对本产品的使用存在疑难或有特殊要求，可以联系本公司各地办事处或经销商，当然您也可以直接致电我公司总部客户服务中心，我们将竭诚为您服务。本手册包含0.75kW～5.5kW功率等级的CDI-D100系列通用变频器使用说明，内容如有变动，恕不另行通知。开箱时，请认真确认以下内容：1、产品在运输过程中是否有破损，零部件是否有损坏、前言脱落，主体是否有碰伤现象。2、本机铭牌所标注的额定值是否与您的订货要求一致，箱内是否包含您订购的机器、产品合格证、用户操作手册及保修单。本公司在产品的制造及包装出厂方面，质量保证体系严格，但若发现有某种检验遗漏，请速与本公司或您的供货商联系解决。警告未经书面许可,不得翻印、传播或使用本手册及其相关内容，违者将对所造成的损害追究法律责任。目录Ⅰ目录前言第一章安全运行及注意事项················································1第二章产品信息·····································································32.1铭牌数据及命名规则·····················································32.2技术规范········································································42.3CDI-D100系列通用变频器············································62.4外型及安装尺寸····························································72.5日常使用的保养与维护·················································8第三章变频器的安装及接线················································123.1变频器前盖与数字操作键盘的安装···························123.1.1变频器前盖的安装················································123.1.2数字操作键盘的安装············································123.2安装地点及空间的选择···············································133.3主回路的接线及其注意事项·······································153.3.1主回路接线图及其注意事项································153.3.2主回路输入侧的接线注意事项····························163.3.3主回路输出侧的接线注意事项····························183.4控制电路的接线··························································203.4.1控制电路端子排列及接线图·································203.4.2控制电路端子的功能············································223.5接地··············································································24目录Ⅱ第四章键盘操作与运行·······················································254.1操作方式的选择··························································254.2试运行及检查······························································254.2.1试运行前的注意事项及检查································254.2.2试运行···································································264.2.3运行时的检查·······················································264.3键盘的操作方法··························································274.3.1键盘按键及功能····················································274.3.2键盘显示方式·······················································274.3.3查看/设定参数的方法（用数字键盘）···············294.3.4键盘设定频率的方法············································30第五章功能参数表·······························································31第六章功能参数说明···························································476.1基本功能参数P00组··················································476.2辅助功能参数P01组··················································636.3输入输出端子与多段速运行功能P02组···················746.4多段速运行功能P03组···············································926.5其他功能参数P04组··················································986.6显示功能参数P05组················································105第七章故障排除·································································1067.1故障的诊断与排除措施·············································1067.2报警显示和解释························································1087.3电机故障和排除措施·················································108附录RS-485通讯协议修正················································110第一章安全运行及注意事项第1页第一章安全运行及注意事项CDI-D100系列通用变频器安装、运行、维护和检查之前要认真阅读本说明书。为了确保您的人身、设备及财产安全，在使用我公司的CDI-D100系列通用变频器之前，请务必仔细阅读本章内容。说明书中有关安全运行的注意事项分类成“警告”和“注意”。：指出潜在的危险情况，如果没有按要求操作，可能会导致人身重伤或者死亡的情况。：指出潜在的危险情况，如果没有按要求操作，可能会导致人身轻度或中度的伤害和设备损坏。这也可对不安全操作进行警戒。安全运行的注意事项：1.安装、维护作业只能由专业人员进行操作。2.核实变频器的额定电压必须和AC电源电压等级相一致。警告注意警告第一章安全运行及注意事项第2页3.切勿使AC主回路电源和输出端子U，V和W相连接。连接时变频器会损坏，并且保修单失效。4.只能在装好面板后才能接通输入电源，通电时不要卸去外盖。5.切勿触摸变频器内的高压端子。6.电路通电时不要连接或断开导线及连接器。7.CMOS元件容易被静电损坏，请不要触碰CMOS元件。8.此变频器不能进行耐压试验。1.请勿随意更改变频器厂家参数。否则可能造成设备损坏。2.存贮时间超过半年以上的变频器,上电时应先用调压器逐渐升压,否则有触电和爆炸的危险。3.应在断开电源10分钟后进行维护操作,此时充电指示灯彻底熄灭或确认正负母线电压在36V以下,否则有触电的危险。4.必须由专业人员更换零件.严禁将线头或金属物遗留在机器内,否则有发生火灾的危险。5.更换控制板后,必须在运行前进行相应的参数设置,否则有损坏财物的危险。注意警告第二章产品信息第3页第二章产品信息2.1铭牌数据及命名规则铭牌数据:以型号CDI-D100G1R5T4为例:铭牌数据型号说明CDID100G1R5T4德力西变频器产品设计序号适配电动机功率（kW）G0R75=通用0.75kWG1R5=通用1.5kWG2R2=通用2.2KwG3R7=通用3.7kWG5R5=通用5.5kW电压等级（额定电压）：T2=220VT4=380VT6=660V第二章产品信息第4页2.2技术规范调制方式空间电压矢量控制方式V/F控制频率设定分辩率数字量:0.01Hz模拟量:0.05Hz/50Hz,输出频率范围:0–400Hz频率精度数字:昀大输出频率的0.02%模拟:昀大输出频率的0.1%过载能力额定电流150%—1分钟，额定电流200%—0.5秒V/F比率线性,平方,任意折线V/F控制转矩补偿手动转矩补偿(0-30%)运行方式键盘/端子/RS485通讯可通过多种方式随时切换频率设定模拟电压给定、模拟电流给定、脉冲给定、键盘给定、RS485通讯给定可通过多种方式随时切换启动信号正转,反转多段速度至多可以设定8个速度(使用多功能端子)加减速时间0.1-6000秒，加减速时间可切换加减速方式：线性、S曲线紧急停止中断变频器的输出寸动慢速运行自动运行通过设定的参数自动运行(7段速度)运行输入信号故障复位当保护功能处于有效状态时，可以自动复位故障状态。第二章产品信息第5页运行状态频率检测等级，过载报警，过电压，欠电压，运行，停止，恒速，自动程序运行，变频器过热故障输出触点输出：交流250V3A,直流30V3A输出信号模拟输出从输出频率，输出电流，输出电压、VF1、VF2、︱VF1-VF2︱中选择(输出电压:0-10V，2-10V，0-20mA，4-20mA)运行运行功能直流制动，频率限制，跳频，滑差补偿，反转保护，PID控制，计数，定长，能耗制动，风扇可控等变频器保护恒速过流、加速过流、减速过流、恒速过压、加速过压、减速过压、欠压、过热、过载、外部故障保护、输入缺相保护保护功能瞬间掉电小于15毫秒：连续运行大于15毫秒：允许自动重新启动运行信息设定频率、输出电流、输出电压、母线电压、输入信号、反馈值、模块温度、输出频率、电机同步转速、电机速度。（可设定P05.00-P05.22）显示键盘错误信