搜索
i目录1设备简介············································································································································1-12安装准备············································································································································2-12.1安全注意事项·····································································································································2-12.2检查安装条件·····································································································································2-12.2.1温度、湿度要求······················································································································2-12.3设备附件············································································································································2-22.4安装工具············································································································································2-23安装AP···············································································································································3-13.1安装流程············································································································································3-13.2安装前检查········································································································································3-13.3安装AP··············································································································································3-13.4连接AP电源·······································································································································3-43.4.1上电前检查······························································································································3-43.4.2PoE供电··································································································································3-43.4.3本地供电·································································································································3-43.4.4上电后检查······························································································································3-53.5将AP连接到网络································································································································3-53.5.1查看FitAP是否连接到网络·····································································································3-63.5.2查看FatAP是否连接到网络····································································································3-64登录FatAP········································································································································4-14.1通过Telnet或者Web方式登录设备·····································································································4-11-11设备简介H3CWA4320H-ACN无线接入点（以下简称WA4320H-ACN）可作为FitAP与有线无线一体化交换机/无线控制器配合使用，所有配置任务由有线无线一体化交换机或无线控制器完成，也可单独工作在FatAP模式为WLAN（WirelessLocalAreaNetwork）用户提供无线接入服务。WA4320H-ACN基本配置如下表。表1-1产品基本配置列表产品型号产品适用协议和特点天线功耗WA4320H-ACN•IEEE802.11a/b/g/n/ac•双射频内置智能天线：•2.4G增益2dBi•5G增益2dBi10WWA4320H-ACN的外形尺寸及重量如下表。表1-2外形尺寸及重量产品型号外形尺寸重量WA4320H-ACN（H×W×D）150mmx86mmx35mm240g2-12安装准备本章主要包含以下内容：2.1安全注意事项2.2检查安装条件2.3设备附件2.4安装工具2.1安全注意事项仅允许专业人员进行设备及其附件的安装和拆卸工作，进行安装和操作前必须仔细阅读设备提供的相关安全介绍。•采取适当的安全措施避免人身伤害和设备损坏。•请将设备放置在干燥、平整的地方，并且做好防滑措施。•保持设备洁净无灰尘。•不要把设备放置在潮湿的地方，避免设备接触液体。•请不要将设备和安装工具放在行走区域内。2.2检查安装条件在准备安装之前，还应该对设备的安装条件进行检查，以保证设备长期处于良好的运行环境之中。可从以下方面对安装条件进行检查。2.2.1温度、湿度要求设备工作的温度、湿度环境要求如下：表2-1设备工作温度、湿度指标项目取值范围标准工作环境温度（室内）-10℃～55℃存储温度-40℃～70℃工作湿度（非凝露）5%～95%2-22.3设备附件WA4320H-ACN随机发货的附件如下。×2×1×1M3.5×25螺钉M2.9×4螺钉防盗型M2.9×4螺钉备份MAC标签壁挂安装件2.4安装工具在安装WA4320H-ACN时，可能需要用到下列的工具（以下工具需要用户自备）。剥线钳十字螺丝刀梅花顶针螺丝刀压线钳3-13安装AP本章主要包含以下内容：3.1安装流程3.2安装前检查3.3安装AP3.4连接AP电源3.5将AP连接到网络3.1安装流程图3-1AP设备安装流程图3.2安装前检查安装AP前，请先进行以下检查：•请先给AP供电并将AP接入到以太网，检查指示灯状态，确定AP可以正常工作，设备指示灯状态请参见附录A。•请确认在需要安装AP设备的地点已经完成布线工作。•WA4320H-ACN支持802.3af标准的PoE（PoweroverEthernet，以太网供电）电源，如想获得最大的性能，推荐用户使用千兆连接方式。•请先记录AP设备的MAC地址和序列号（MAC地址和序列号标识在AP设备背面），便于后续查找使用。3.3安装AP请按照如下步骤将安装AP：3-2(1)如下图所示，使用M3.5×25螺钉将壁挂安装件固定到接线盒。图3-2固定壁挂安装件到接线盒(2)如下图所示，连接线缆到AP背面的Uplink/PoEIn接口和PassThrough接口。图3-3连接线缆3-3AP背面和下方的PassThrough接口均为标准的RJ-45接口，可以用于连通电话线或根据用户实际需要进行连接。(3)如下图所示，将AP背面的安装孔对准安装架上的突出部分的下沿。图3-4固定AP到壁挂安装件(4)如下图所示，将安装架上的突出部分安装到AP的安装孔然后向下按压AP，将AP固定住，最后拧紧AP侧面的螺钉(该螺钉可选择M2.9×4螺钉或者防盗型M2.9×4螺钉)3-4图3-5固定AP3.4连接AP电源WA4320H-ACN支持本地供电和802.3af标准PoE方式供电，用户可以根据实际网络环境选择供电方式。3.4.1上电前检查AP安装完毕后，每次上电前均要进行检查，检查事项如下：•AP设备采用本地供电时，请确认本地交流电源良好接地。•AP设备采用802.3af标准PoE供电时，请确认PoE供电设备良好接地。3.4.2PoE供电如图3-6所示，可以使用以太网线连接AP设备的以太网接口和支持PoE功能的交换机给AP供电。3.4.3本地供电电源适配器及电源线不随机附带，请用户自行选购。123-5表3-1电源适配器规格项目描述电源适配器输入100-240VAC电源适配器输出+48V0.52AWA4320H-ACN支持AC/DC电源适配器供电，用户可以通过电源适配器将设备的电源接口与本地电源连接后便可实现本地供电。3.4.4上电后检查AP电源连接好后需要检查AP设备的指示灯是否正常显示。设备指示灯状态的详细描述请参见附录A。3.5将AP连接到网络AP设备在实际使用中，可以通过以太网口上行接入Internet或城域网。将AP设备的上行以太网口与以太网交换机的端口连接，实现AP设