建筑工程安全技术交底范本

1目录一、安全技术交底····················61、钢筋作业·······················62、砼施工作业·····················103、木工支模作业····················124、砌筑工程作业····················135、脚手架搭设、拆除作业················166、土方开挖作业····················177、马道、护头棚····················188、卸料平台搭设作业··················199、防水作业······················2110、库房防水材料管理··················2211、调漆作业······················2312、喷漆作业······················2413、屋面防水作业····················2514、油漆作业······················2615、大模板施工作业···················2916、钢结构施工作业···················3217、清理、清运作业···················3318、钢管、料具码放作业·················3419、安全网支搭作业···················3520、抹灰作业······················3621、吊顶作业······················3922、玻璃安装作业····················4023、大理石干挂作业···················4124、玻璃幕墙安装作业··················4225、外墙抹灰作业····················43226、外墙涂料作业····················4427、外爬架作业·····················4528、外挂架作业·····················4629、挑脚手架作业····················4930、拆除工程作业····················5131、回填土作业·····················5332、内外墙面砖、地砖粘贴作业··············5533、井字架搭拆作业···················5634、管道施工、水暖工作业················6335、外电线路防护架搭拆作业···············6536、电焊作业······················6737、现场临时用电作业··················6938、冬季施工用电作业··················7039、一级(A)配电柜安装作业···············7240、二级(B)配电箱安装作业···············7441、三级(C)配电线安装作业···············7642、塔吊上镝灯安装作业·················7743、木工设备照明安装作业················7844、流动箱、手提箱安装使用作业·············7945、砼振捣器接线使用作业················8046、低变照明安装作业··················8147、办公区、生活区食堂用电设备安装作业·········8248、雨季施工用电作业··················8449、打夯机使用作业···················8650、消防水泵安装作业··················8751、气焊、气割作业···················8852、电焊机的安装搬运和使用作业·············9053、塔吊作业（含群塔作业）···············9254、外用电梯安装使用作业················94355、电动吊篮的安装、调试、使用·············9556、无齿切割机切割作业·················10757、圆盘锯使用·····················10858、车、机床加工操作作业················10959、塔吊、外用电梯的拆立作业··············11060、汽车吊吊装作业···················11261、信号指挥作业····················11362、机具切割作业····················11463、通风及设备安装作业·················11564、路基工程作业····················11765、路面工程作业····················12166、旧路面凿除作业···················12367、推土机、安装机作业·················12468、炊事作业······················12769、大临设施施工作业··················12870、库房保管······················13071、铁件加工作业····················13172、暗挖作业······················13373、物料装卸作业····················13874、绿化作业······················13975、砼地泵（含布料杆）·················14076、塔机操作······················14177、搅拌作业······················14278、放线测量作业····················14379、挂勾工操作·····················14480、场内运输作业····················145二、各工种安全操作规程·················1461、土方工程安全操作规程·················1462、桩基工程的安全操作规程················14643、砌体工程的安全操作规程················1474、钢筋工安全操作规程··················1485、混凝土(回填土)工安全操作规程·············1496、结构安装安全操作规程·················1507、油漆工安全操作规程··················1518、木工安全操作规程···················1529、架子工安全操作规程··················15410、卷扬机司机安全操作规程···············15611、测量放线工安全操作规程···············15612、电焊工安全操作规程·················15713、气焊工安全操作规程·················15814、抹灰工安全操作规程·················15915、电工安全操作规程··················16016、信号工安全操作规程·················16017、机动翻斗车司机安全操作规程·············16118、塔式起重机司机安全操作规程·············16219、外用电梯司机安全操作规程··············16320、水暖、电气、通风安装人员安全操作规程········16321、搅拌机司机安全操作规程···············16522、起重工安全操作规程·················16623、劳务普工安全操作规程················1685安全技术交底表C2—1编号工程名称福佳斯·南湖花园一标段交底日期年月日施工单位福建路港（集团）有限公司分项工程名称钢筋工程交底提要交底内容：1.进入施工现场人员必须正确戴好合格的安全帽，系好下颚带，锁好带扣；2.作业时必须按规定正确使用个人防护用品，着装要整齐，严禁赤脚和穿拖鞋、高跟鞋进入施工现场；3.在没有可靠安全防护设施的高处（2米以上含2米）和陡坡施工时，必须系好合格的安全带，安全带要系挂牢固，高挂低用，同时高处作业不得穿硬底和带钉易滑的鞋，穿防滑胶鞋；4.新进场的作业人员，必须首先参加入场安全教育培训，经考试合格后方可上岗，未经教育培训或考试不合格者，不得上岗作业；5.从事特种作业的人员，必须持证上岗，严禁无证操作，禁止操作与自己无关的机械设备；6.施工现场禁止吸烟，禁止追逐打闹，禁止酒后作业；7.施工现场的各种安全防护设施、安全标志等，未经领导及安全员批准严禁随意拆除和挪动。一、钢筋绑扎：1.绑扎基础钢筋，应按规定安放钢筋支架、马镫，铺设走道板（脚手板）；2.在高处（2米以上含2米）绑扎立柱和墙体钢筋时，不得站在钢筋骨架上或攀登骨架上下，必须搭设脚手架或操作平台和马道。脚手架应搭设牢固，作业面脚手板要满铺、绑牢，不得有探头板、非跳板，临边应搭设防护栏杆和支挂安全网；3.绑扎圈梁、挑梁、挑檐、外墙和边柱等钢筋时，应站在脚手架或操作平台上作业；4.脚手架或操作平台上不得集中码放钢筋，应随使用随运送，不得将工具、箍筋或短钢筋随意放在脚手架上；5.严禁从高处向下方抛扔或从低处向高处投掷物料；6.在高处楼层上拉钢筋或钢筋调向时，必须事先观察运行上方或周围附近是否有高压线，严防碰触；7.绑扎钢筋的绑丝头，应弯回至骨架内侧，暂停绑扎时，应检查所绑扎的钢筋或骨架，确认连接牢固后方可离开现场；8.六级以上强风和大雨、大雪、大雾天气必须停止露天高处作业。在雨、雪后和冬季，露天作业时必须先清除水、雪、霜、冰，并采取防滑措施；审核人交底人接受交底人1、本表头由交底人填写,交底人与接受交底人各保存一份，安全员一份；2、当做分部、分项施工作业安全交底时,应填写“分部、分项工程名称”栏；63、交底提要应根据交底内容把交底重要内容写上。安全技术交底表C2—1编号工程名称交底日期年月日施工单位分项工程名称钢筋作业交底提要交底内容：9.要保持作业面道路通畅，作业环境整洁；10.作业中出现不安全险情时，必须立即停止作业，撤离危险区域，报告领导解决，严禁冒险作业。二、钢筋加工：（一）冷拉：1.作业前，必须检查卷扬机钢丝绳、地锚、钢筋夹具、电气设备等，确认安全后方可作业；2.冷拉时，应设专人值守，操作人员必须位于安全地带，钢筋两侧3米以内及冷拉线两端严禁有人，严禁跨越钢筋和钢丝绳，冷拉场地两端地锚以外应设置警戒区，装设防护挡板及警告标志；3.卷扬机运转时，严禁人员靠近冷拉钢筋和牵引钢筋的钢丝绳；4.运行中出现滑脱、绞断等情况时，应立即停机；5.冷拉速度不宜过快，在基本拉直时应稍停，检查夹具是否牢固可靠，严格按安全技术交底要求控制伸长值；6.冷拉完毕，必须将钢筋整理平直，不得相互乱压和单头挑出，未拉盘筋的引头应盘住，机具拉力部分均应放松再装夹具；7.维修或停机，必须切断电源，锁好箱门。（二）切断：1.操作前必须检查切断机刀口，确定安装正确，刀片无裂纹，刀架螺栓紧固，防护罩牢靠，空运转正常后再进行操作；2.钢筋切断应在调直后进行，断料时要握紧钢筋，罗纹钢一次只能切断一根；3.切断钢筋，手与刀口的距离不得小于15㎝。断短料手握端小于40㎝时，应用套管或夹具将钢筋短头压住或夹住，严禁用手直接送料；4.机械运转中严禁用手直接清除刀口附近的断头和杂物，在钢筋摆动范围内和刀口附近，非操作人员不得停留；5.作业时应摆直、紧握钢筋，应在活动切口向后退时送料入刀口，并在固定切刀一侧压住钢筋，严禁在切刀向前运动时送料，严禁两手同时在切刀两侧握住钢筋俯身送料；审核人交底人接受交底人1、本表头由交底人填写,交底人与接受交底人各保存一份，安全员一份；2、当做分部、分项施工作业安全交底时,应填