HPDC交换机交维手册

1HPDCSANBackbone交换机日常维护指导手册2目录1、目的.........................................................................................................................................32、适用范围.................................................................................................................................33、硬件设备信息概述.................................................................................................................34、登录及配置.............................................................................................................................34.1建立一个串行链接，登录到DCSANDirector.........................................................34.2配置IP地址.................................................................................................................44.3建立以太网连接...........................................................................................................54.4定制一个交换机的名字...............................................................................................54.5定制一个机箱的名字...................................................................................................64.6设置domainID............................................................................................................64.7验证端口识别模式并连接...........................................................................................64.8使用软件许可证...........................................................................................................64.9备份配置.......................................................................................................................65、zone配置方法.......................................................................................................................65.1查看zone配置...........................................................................................................75.2创建别名.......................................................................................................................85.3创建zone(把别名或端口分配到zone中)..............................................................85.4创建zone配置文件(把zone加入到配置文件中)................................................85.5使zone配置生效.......................................................................................................85.6保存配置........................................................................................................................96、常用命令及解释...................................................................................................................1031、目的为保障*****中心HPDCSANBackbone交换机设备的高效、稳定运行，制订本指导手册。本手册详细描述了日常检查的主要步骤，从而指导现场工程师对其进行监控和维护。2、适用范围使用者为****有限公司心工程师。3、硬件设备信息概述服务器数量：2台，基本信息如下：序号设备名称设备品牌设备型号基本配置数量1光纤通道交换机HPHPHSTNM-N014HPDCSANBackBone交换机2台，每台配置：3x48口端口板，136x8GbSFP,8*25KM8Gb短波模块，冗余电源24、登录及配置4.1建立一个串行链接，登录到DCSANDirector1.通过确认LED指示灯均为稳定的绿灯来确认DCSANDirector已启动，POST已完成。2.从活跃CP的服务端口移除shippingcap，用DCSANDirector的串行电缆把服务端口和电脑的工作区域相连接。3.通过终端应用程序(如Windows环境下的HyperTerminal或者Unix环境下的TERM)来访问DCSANDirector。4.关闭运行在工作区域的任何串行通信程序（如同步程序）。5.打开终端模拟应用程序并按如下方式配置：a.对于MicrosoftWindows系统：Bitspersecond—9600Databits—8Parity—NoneStopbits—14Flowcontrol—Noneb.对于UNIX系统：tip/dev/ttyb-9600当终端模拟应用程序不再更新信息，按Enter键接下来登录会出现：CP0ConsoleLogin:6.以admin登录DCSANDirector，默认密码是password7.修改密码密码可以8-40个字符长4.2配置IP地址DCSANDirector默认的IP地址和主机名为：10.77.77.75/CP0(配置时，CP刀片在槽6)10.77.77.74/CP1(配置时，CP刀片在槽7)为CP刀片配置IP地址：1.以admin登录activeCP2.通过ipaddrset-sw0指令配置IP地址：swDir:adminipAddrSet-sw03.通过ipaddrset-cp0指令:swDir:adminipAddrSet-cp0建立CP0IP地址4.SetuptheCP1IPaddress通过ipaddrset-cp1指令配置CP1IP地址:swDir:adminipAddrSet-cp1配置IP地址如下例：swDir:adminipaddrset-sw0EthernetIPAddress[0.0.0.0]:123.123.123.120EthernetSubnetmask[0.0.0.0]:123.123.123.123FibreChannelIPAddress[0.0.0.0]:FibreChannelSubnetmask5[0.0.0.0]:IssuinggratuitousARP...Done.Committingconfiguration...Done.swDir:adminipaddrset-cp0HostName[cp0]:EthernetIPAddress[10.77.77.75]:123.123.123.121EthernetSubnetmask[0.0.0.0]:123.123.123.123GatewayIPAddress[0.0.0.0]:123.123.123.124IPaddressisbeingchanged...Done.Committingconfiguration...Done.swDir:adminipaddrset-cp1HostName[cp1]:EthernetIPAddress[10.77.77.74]:123.123.123.122EthernetSubnetmask[0.0.0.0]:123.123.123.123GatewayIPAddress[0.0.0.0]:123.123.123.124IPaddressofremoteCPisbeingchanged...Done.Committingconfiguration...Done.5.执行reboot命令，重启DCSANDirector。4.3建立以太网连接1.从activeCP刀片的以太网端口移除shipping插头。2.从以太网电缆的一端插入以太网端口。3.从另一端连接Ethernet10/100/1000Base-TLAN。4.4定制一个交换机的名字1.用新名字进入switchName：swDir:adminswitchNameswBrocadeDCX5Committingconfiguration...Done.swBrocadeDCX5:admin2.记录该新名字。64.5定制一个机箱的名字1.按以下步骤进入chassisNameswitch:adminchassisnameDCX_chassis_1软件显示如下信息:Committingconfiguration...2.记录该新名字。4.6设置domainID1.输入switchDisable指令2.输入configure指令3.输入“y”：Fabricparameters(yes,y,no,n):[no]y4.输入domainID：Domain:(1.239)[1]35.按剩下的提示完成,或者按Ctrl+D接受设置并退出。6.输入switchEnable指令来启动DCSANDirector。4.7验证端口识别模式并连接4.8使用软件许可证输入licenseShow指令：swDir:adminlicenseshowAAbbccDDeeFFeeGG:WeblicenseZoninglicenseExtendedFabriclicenseFabricWatchlicensePerformanceMonitorlicenseTrunkinglicenseSecuritylicense4.9备份配置简便方法为备份