CDS50安装使用说明

CDS快速使用说明北京惠捷朗科技有限公司第1页共34页CDS快速使用说明一．测试工具的准备工作···················································································21．1．测试准备分步走················································································21．2．SAGEM手机设置··············································································31．3．SAGEM手机连接及设置·····································································41．4．商用手机连接及设置··········································································71．5．SAGEM手机和商用手机拨号建立························································10(1).添加拨号网络···················································································································10(2).更改拨号网络属性···········································································································11(3).创建SAGEM另一个拨号连接························································································13(4).创建Nokiacmwap拨号···································································································13二．CDS测试设置···························································································16三．CQT测试项目配置·····················································································17四．DT测试项目配置······················································································25五．视图和分析·······························································································295．1．视图管理························································································295．2．分析插件管理··················································································30（1）地理分析：GoogleEarth·····························································································30（2）地理分析：MapX·········································································································31（3）数据时间图···················································································································32（4）统计：IE数据··············································································································32（5）统计：事件···················································································································33六.报告生成··································································································33CDS快速使用说明北京惠捷朗科技有限公司第2页共34页一．测试工具的准备工作1．1．测试准备分步走1.计算机应保证1.2G以上主频，256M以上内存2.重新安装WindowXPSP1或SP2操作系统，不能安装与测试无关的其它软件，尤其是网络相关软件。3.将系统中的任何与网络通讯相关的程序关闭，如MSNQQ等。4.关闭Windows的自动更新功能，在我的电脑上右键点击选择“属性”，在弹出的对话框中的“自动更新”栏中去除自动更新功能。5.关闭所有防火墙，如下图：CDS快速使用说明北京惠捷朗科技有限公司第3页共34页6.Sagem手机为OT490或OT498,串口速率为115200（默认不用设置），自由双频模式，（3+1）或（4＋1）时隙7.商用手机使用Nokia6230、7610（GPRS）或N70（EDGE），以及DUK-2数据线8.为Sagem手机添加Modem并建立两个拨号网络：Sagemcmnet和Sagemcmwap并手动验证拨号连接可以使用。详细方法参见Sagem调制解调器与拨号配制说明。9.安装Nokia调制解调器并建立Nokiacmwap拨号连接，注意APN必须设置为cmwap10.安装CDS测试软件11.全部安装成功后使用Windows的系统还原功能创建一个还原点，已防止将来系统被病毒感染等异常情况后快速恢复系统。单击“开始、所有程序、系统工具、系统还原”，在弹出的对话框中选择“创建一个还原点”，然后根据提示操作。如果需要进行系统还原前，注意应将已测试的日志文件备份出来。或将系统做GHOST备份。1．2．SAGEM手机及GPS设置设置手机支持网络版本1.按▲或▼键，选择Testtool,按Select键；2.按▲或▼键，选择Info&settings,按Select键；3.按▲或▼键，选择Release,按OK键；4.按▲或▼键，选择Release97,按OK键；如果测试EDGE则选择Release4设置手机的时隙配置1.按▲或▼键，选择Testtool,按Select键；2.按▲或▼键，选择Info&settings,按Select键；3.按▲或▼键，选择Mobileinfo,按Select键；4.按▲或▼键，选择Multislotclasses,按Select键；5.按Modify设置GPRSmultislotclass[4(3+1)]和E-GPRSmultislotclass[8(4+1)]时隙（根据测试的需要选择相应的信道配置）CDS快速使用说明北京惠捷朗科技有限公司第4页共34页关闭彩信自动提取：1.按▲或▼键，选择短信息,按选择键；2.按▲或▼键，选择选项,按选择键；3.按▲或▼键，选择多媒体信息,按选择键；4.按▲或▼键，选择高级设定,按选择键；5.按▲或▼键，进入忽略MMS,选项选择.SMS消息模式选择1.按▲或▼键，选择Testtool,按Select键；2.按▲或▼键，选择Info&Settings,按Select键；3.按▲或▼键,选择GPRSsettings,按Select键；4.按▲或▼键,选择SMSmode,按Select键；5.按▲或▼键,选择GSMonly,按Select键；SAGEMOT490连接设置1.按▲或▼键，选择Connectivity,按Select键；2.按▲或▼键，选择Info&Settings,按Select键；3.按▲或▼键,选择USBMode,按Select键；4.按▲或▼键,选择Modem,按Validate键；GPS手机设置1.蓝牙GPS主要是配置电脑的蓝牙模块和蓝牙GPS之间的通信，配对及使用一个虚拟的COM口，CDS的GPS设备就连接到该COM端口2.USB的GPS模块主要是安装GPS的连接线驱动，安装完成后系统会将GPS的连接默认一个端口，该端口的COM口号就是CDS连接GPS硬件的接口3.串口（serial）的GPS则需要电脑提供一个串口连接，且手持GPS机要将接口设置成NMEA48001．3．SAGEM手机连接及设置打开sagem数据线驱动程序2007XXX_Sagem_USB_Drivers_setup(该驱动不断更新)双击安装。如图：CDS快速使用说明北京惠捷朗科技有限公司第5页共34页插入SAGEMOT490、498的USB数据线，等系统发现硬件以后点击下一步下一步重新拔插数据线,系统将自动安装驱动CDS快速使用说明北京惠捷朗科技有限公司第6页共34页完成！打开‘设备管理器’双击SagemUSBMobilepseudoCDCTrace调制解调器，在‘属性’的‘调制解调器’里面查看端口，该端口就是CDS4.0软件在连接SAGEM手机所用的端口。如图:安装后会自动添加两个调制解调器，分别做为trace和Modem的用途CDS快速使用说明北京惠捷朗科技有限公司第7页共34页该端口为CDS连接sagem的端口SAGEMUSBMobilepseudoCDCModem该modern为拨号的数据口，先双击设置初始化命令，+cgdcont=1,”IP”,”cmnet”;+cgdcont=2,”IP”,”cmwap”(注:输入时用英文输入法)如图：并用这个modern在‘网络连接’建立拨号连接cmnet、和cmnet1．4．商用手机连接及设置CDS在测试某些项目时要用到一部商用手机来作为发送短信、彩信（SMS、MMS）的终端，我们要对其做设备连接以及相应设置，以下是它的连接设置：硬件要求：商用手机nokia7610、nokia6230或N70笔记本电脑与手机相匹配的数据线以及驱动软件安装后硬件如图：CDS快速使用说明北京惠捷朗科技有限公司第8页共34页安装步骤如下：连接数据线和手机将驱动光盘放入CD－rom中添加新设备的驱动完成上述步骤以后，打开“控制面板”里的“电话和调制解调器选项”如图设置以商用手机为终端的modern如图安装完手机驱动会自动分配一个端口和安装一个modernCDS快速使用说明北京惠捷朗科技有限公司第9页共34页初始化命令为：+cgdcont=1,”ip”,”cmwap”新建一个连接,其中ISP名称为：nokia(不一定要这个名称)拨号为：*99***1#和手机数率一致,不同手机数率不一样CDS快速使用说明北京惠捷朗科技有限公司第10页共34页1．5．SAGEM手机和商用手机拨号建立(1).添