威士伯汽车油漆介绍与使用..

HISTORYOFDEBEER德倍尔(DeBeer)的历史1910tradecompany开始组建贸易公司1950ownproductionplant拥有自己的制造工厂1980mixingsystemsseries200&400混合系统200&400系列问世1988mixingsystemseries500混合系统500系列问世1996firstwater&HSproducts开发第一代出水性及HS产品1999mixingsystemswater&HS开发出混合水性及HS系统产品2001independentcompany设立独立的公司ProductGroups产品1.0cleaners清洁剂2.0putties原子灰3.0primers底漆4.0fillers/surfacers中涂漆5.0topcoats面漆6.0clearcoats清漆7.0hardeners固化剂8.0thinners稀释剂9.0additives添加剂1.0CLEANERS清洁液1.1DegreasingAgent1-951脱脂清洁剂1.2AntistaticDegreaser1-851抗静电清洁剂1.3DegreasingAgentWaterbase9-851水性去油污剂1.4GuncleanerWaterbase9-852喷枪清洁剂---水性2.0PUTTIES腻子2.1universalpolyesterPUTTY1.900通用原子灰2.2polyesterPUTTYfine1.910幼细原子灰2.3standardpolyesterPUTTY1.930标准原子灰2.4polyesterglassFIBREPUTTY1.940玻璃纤维原子灰2.5polyesterPUTTYsoft1.960柔韧原子灰2.6polyesterPUTTYALUMINIUM1.970铝合金原子灰2.7polyesterspray-filler1.980原子灰喷灰2.8NCcarfiller6-022填眼灰3.0PRIMERS底漆3.1WashPrimer1-15防侵蚀底漆3.2WashPrimerCH1-17磷化底漆CH3.3EpoxyPrimer1-75环氧底漆3.41KAcrylicPrimer1-36单组份底漆3.5PlasticPrimer1-60塑料底漆3.1WASHPRIMER1-15磷化底漆1-15FEATURES&BENEFITS特性和优点GoodAdhesiononbaremetalandzinconpassengercars.在镀锌板和钢板上有极佳的附着力Shortflashofftime表干时间特短Goodrustprotection可作为面漆４００及７００系列的基层底漆使用3.1.1WASHPRIMER1-15磷化底漆1-151:1withWashprimerActivator1-10以1:1与防侵蚀底漆固化剂1-10混合1-2layer喷1~2层1.3–1.5GravityFeed/1.6–1.8SuctionFeed可适用于重力型上壶喷枪:1.3~1.5/吸力型下壶喷枪:1.6~1.8Flash-offtime:10–15minutes闪干时间:10~15分钟Dryingtime30mins.at60°C/2hrsat20°C干燥时间:60°C干燥30分钟/20°C干燥2小时3.2WASHPRIMERCH1-17磷化底漆CH1-17FEATURES&BENEFITS特性和优点GoodAdhesionondifficultsubstrateslikealuminiumandothernonFerrometals.Usedoncommercialvehicles在不锈钢，铝合金等金属表面上具极佳的附着力，特别适合用于商用车和飞机板材ContainsChrome-mate含有铬酸盐Slowflashoffforlargeobjectsorhightemperatures由于表干比较慢特别适用于大面积和温度较高的环境下施工3.2.1WASHPRIMER1-17磷化底漆1-171:1withWashprimerActivator1-12以1:1与防侵蚀底漆固化剂1-12混合1–３layer可选择施喷１涂层为防锈底漆／３涂层为中涂1.３–1.５GravityFeed/1.6–1.8SuctionFeed可适用:重力型上壶喷枪1.３~1.５/吸力型下壶喷枪:1.6~1.8Flash-offtime:１０－１５minutes闪干时间:１０－１５分钟Dryingtime:３０min.at60°C./2hrs.at20°C.干燥时间:60°C干燥３０分钟/20°C干燥2小时3.3EpoxyPrimer1-75环氧底漆1-75FEATURES&BENEFITS特性与优点GoodAdhesionondifficultsubstrateslikegalvanised&stainlesssteel,etc.对不同金属板材上都具有极佳的附着力如：铝合金，不锈钢，玻璃纤维板材Goodrustprotection良好的防腐，防锈能力Polyesterputtiescanbeappliedontop如采用1-17040特快干ＥＰ固化剂，原子灰可直接使用在已干的漆面上3.3.1EpoxyPrimer1-75环氧底漆1-75~2:1withEpoxyHardener1-70.Forwet-on-wetuseadd20-25%UniThinner以2:1调配，使用１－７０／1-7040EP固化剂.当湿对湿喷涂时,需加２５-３０%ＵＮＩ稀释剂.1layerforawet-on-wetsystem/3layersforafiller可选择湿对湿1喷涂层或中涂漆的３涂层1.3–1.7GravityFeed/1.6–1.8SuctionFeed可适用于重力型上壶喷枪1.3~1.7/吸力型下壶喷枪:1.6-2.0Flash-offtime:45-60minuteswet-on-wet每涂层相隔时间:湿对湿喷涂需45~60分钟，选择为中涂层用10-15分钟Dryingtime:60min.at60°C./24hrs.at20°C.干燥时间:60°C干燥60分钟/20°C干燥24小时3.5.PlasticPrimer1-60塑料底漆1-60FEATURES&BENEFITS特性和优点Readyforuse可直接使用Unlimitedpotlife无限制使用时间Fastdrying快干Goodadhesiononmostplastics能与大部分塑料有较优良的附着性能3.5.1PlasticPrimer1-60塑料底漆1-60Readyforuse可直接使用1thinlayer.只需喷1薄层1.3–1.5GravityFeed/1.6–1.8SuctionFeed适用于:重力型上壶喷枪1.３~1.５/吸力型下壶喷枪:1.6~1.8Flash-offtime:untilmatt.每涂层相隔时间：表面呈哑光状4.0FILLERS/SURFACERS中涂漆4.12KSurfacer1-472K中涂4.5HSSurfacer8-145HS高浓度中涂4.2MSFillingPrimer1-146MS4-1中涂；杏．灰色4.3NonSandingFiller1-746免磨中涂4.4HSNonSandingFiller30-746HS免磨中涂4.6HSTintingSurfacer8-149HS高浓度调色中涂4.12KSurfacer1-472K中涂1-47FEATURES&BENEFITS特性和优点Costeffectivefiller填充力强，易打磨Fastcuring快干4.1.12KSurfacer1-472K中涂1-474:1with2KorMSHardener以4:1与2K或MS固化剂混合２–３layers喷２~３层1.6–1.8GravityFeed/1.6–1.8SuctionFeed适用于:重力型上壶喷枪1.6~1.吸力型下壶喷枪:1.6~1.8Flash-offtime:untilmatt涂层间隔时间:表面呈亚光约10分钟Dryingtime:30min.at60°C./8hrs.at20°C.干燥时间:60°C干燥30分钟/20°C干燥8小时4.2MSFillingPrimer1-146MS4-1中涂1-146FEATURES&BENEFITS特性和优点Goodfilmbuild极佳的厚膜层Fastdrying快干Goodenamelholdout极佳封密性，易打磨4.2.1MSFillingPrimer1-146MS4-1中涂1-1464:1with2KorMSHardener以4:1与2K或MS固化剂混合2–3layers喷2~3层1.6–1.8GravityFeed/1.6–1.8SuctionFeed适用于:重力型上壶喷枪1.６~1.8/吸力型下壶喷枪:1.6~1.8Flash-offtime:untilmatt涂层间隔时间:表面呈亚光约10分钟Dryingtime:30min.at60°C./6hrs.at20°C.干燥时间:60°C干燥30分钟/20°C干燥6小时4.3NonSandingFiller1-746免磨中涂1-746FEATURES&BENEFITS特性和优点Savinglabour节省人工Verysmoothsurface极其平滑的漆面Goodfilmbuild极佳饱满度Easytouse施喷简单4.3.1NonSandingFiller1-746免磨底漆1-7464:1:1with2KorMSHardenerandThinner以4:1:1与2K固化剂和稀释剂混合1layer1喷涂层1.4–1.6GravityFeed/1.6–1.8SuctionFeed适用于:重力型上壶喷枪1.4~1.6/吸入型下壶喷枪:1.6~1.8Flash-offtime:app.20min涂层间隔时间:约15-20分钟Dryingtime:30min.at60°C.干固时间:60°C干燥30分钟或20c干燥8小时4.4HSNonSandingFiller30-746HS免磨底漆30-746FEATURES&BENEFITS特性和优点CompliantProductVOC合符有害物排放要求Savingmaterial遮盖力强Excellentflow极佳的流平性Goodfilmbuild优良的饱满度Slowflashoff表面干固时间较慢Goodenamelholdout极佳的封密性4.4.1HSNonSandingFiller30-746HS免磨中涂30-7464:1:1withHStopcoathardener/unithinner以4:1:1与HS面漆固化剂和通用型稀释剂混合1layer喷1层1.4–1.6GravityFeed/1.6–1.8SuctionFeed适用于：重力型上壶喷枪：1.4~1.6/吸力型下壶喷枪1.6~1.8Flash-offtime:app.45min/max8hrs.at20°C闪干时间:约45分钟／20°C下最多需8小时Dryingtime:30min.at60°C.干燥时间:60°C干燥30分钟4.5HSSurfacer8-145HS高浓度中涂8-145FEATURES&BENEFITS特性和优点CompliantProductvoc合符有害物排放要求Fastdrying快干Easytosand易打磨Goodfilmbuild极佳的厚膜层Goodenamelholdout极佳封密性4.5.1HSSurfacer8-145HS高浓度中涂漆8-1453:1with2KorMSHardener3:1调配比，使用MS固化剂47/55及5%uni稀释剂2-3layers喷2~3层1.6–1.8G