Fc300-Startup

VLTAutomationDriveFC300安装本节内容包含VLT®AutomationDriveFC300的安装、启动、编程和操作|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|2丹佛斯自动控制管理（上海）有限公司传动与控制部培训专员沈绍炎地址上海市宜山路900号C楼18层电话[phone]手机[phone]|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|3索引A–安装检查B–接线动力电接入电机控制串行通信C–编程快捷菜单主菜单基本操作VLTAutomationDriveFC300安装|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|4警告:触摸电器部分可能触电,即使在设备和AC电源连接断开之后，连接断开之后再等15分钟，确保电容放电结束。VLT®AutomationDriveFC300安装|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|5如果要修改参数–首先按下面板上的OFF键部分参数状态标有“Notwhilerunning”，表明参数不允许在变频器运行期间改变。因此，先按OFF键；让电机停下来，然后改变参数。VLT®AutomationDriveFC300安装|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|6先打开变频器的包装，然后检查变频器名牌是否和订单一致A-安装检查|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|8HptokWChartModelHpkWModelHpkWModelHpkW0.250.185K57.55.575K100.075.0K250.330.257K510.07.590K125.090.0K370.500.3711K15.011.0110150.0110.0K550.750.5515K20.015.0132200.0132.0K751.00.7518K25.018.5160250.0160.01K11.51.122K30.022.0200300.0200.01K52.01.530K40.030.0250350.0250.02K23.02.237K50.037.0315450.0315.03K75.03.745K60.045.0355500.0355.04K05.04.055K75.055.0415600.0415.0A-安装检查FC102和FC202变频器能控制比标称额定功率小4档的电机FC302变频器能控制比标称额定功率大2档或小2档的电机举例:75Hp[55kW]FC202能控制一个30Hp[22kW]电机|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|9运行环境条件干净的和干燥的:5%to95%相对湿度,无结露24小时平均温度极限:113°F[45°C]最高温度极限:122°F[50°C]海拔高度:1000m以上每升高300m降低容量2%，2000m以上，咨询丹佛斯贮藏温度极限:-13°to149°F[-25°to+65°C]A-安装检查|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|10布局允许并列安装上下两排间距10cm除了水平安装，其它布局都可以采纳变频器背板必须直接安装A-安装检查|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|11接线通则金属电线管分开布线专用接地线必备采用力矩搬手拧紧连接件B–接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|12B–接线电源进线接线端子91(L1),92(L2)和93(L3)用于连接动力电源进线。每分钟仅允许2次上电;大功率变频器(90KW)只允许2分钟上1次电。如果安装装了RFI滤波器并且变频器由隔离的电源（IT电源）供电时，应将P14-50设置成[0]。UL标准要求安装熔断器–Bussman等效产品。|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|13B–接线电机接线240Vac变频器输出闭合/切断不受限制输出电缆长度:300m非屏蔽;150m屏蔽端子96(U),97(V)和98(W)连接电机电缆可选–断开12-27之间连接，然后软重启|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|15B-接线电机接线–泵切换便于电机间的轮换工作|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|16控制端子接线控制端子可接的最高电压是24Vdc安全互锁–12&27间接跳接线或转换开关安全停车选项–13&37间接跳接线或转换开关螺丝起子打开端子断开接线B-接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|17控制端子接线–数字输入单刀双投(SPDT)2-线启动/停止用18端子B-接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|18控制端子接线–数字输入单刀双投带中央停止位端子18(P5-10)设成“启动”19(P5-11)设成“启动&反转”B-接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|19控制端子接线–数字输入端子18,19,27,29,32和33–可选43个功能3-线启动/停止瞬动开关,按钮,(NO)接端子18=自锁启动;(NC)端子19=停止反逻辑B-接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|20控制接线–数字输入步进式增加/减少速度参考值(数字电位器)端子32设成“升速”;端子33设成“减速”P3-90设置考参值步长量（%）P3-95设置延迟,P3-91设置考参值从0到100%的时间，例如100sP3-93和P3-94设置考参值极限(可负值)B-接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|22控制接线–数字输入NPN所有数字输入既可是源型(+24Vdc;PNP)或漏型(ground;NPN);参数修改后在下一次上电时生效参考地(端子20)用于激活DI;参数5-00设成NPN.B-接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|23控制接线–模拟输入电位器P3-15参考值#1P6-10和设置电压范围P6-14和6-15设置以rpm为单位设置范围B-接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|24控制接线–模拟输入2-线变送器由端子12或13(+24Vdc)供电AI切至右边则选择电流量B-接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|25控制接线–模拟输出仪表指示端子42仅能作AO输出端子42的功能在参数6-50中设置参数6-51设置最小输出;6-52设置最大输出B-接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|26控制接线–数字输出参数5-01选择端子27作DI或DO参数5-02选择端子29作DI或DO参数5-30&5-31设置功能数字输出由+24Vdc供电如果P5-00设成NPN,DO的公共端子是12B-接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|27控制接线–继电器输出2键入插头:继电器1(01,02,03)和继电器2(04,05,06)C型继电器-最大2A，240V或400VP5-40为继电器1和继电器2设置功能P5-41和5-42设置ON和OFF延迟B-接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|28控制接线–串行通信RS485+接端子68;-接69USB口不需转换,但只能和1FC通信RS232或USB转换成RS485需要转换器，可和多个变频器通信总线终端,线终端电阻由开关切换.连接超过31台之后需加转发器（放大器）B-接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|29B-接线|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|30顶部键Status显示VLT内部发生了什么事QuickMenu允许编程者快速改变某些常用的参数MainMenu允许编程者访问VLT内部所有的参数AlarmLog可读取最新的报警信息C–编程|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|31中间键OK用来选择菜单中一部以改变参数值Cancel取消已经作的改变Up&Down让菜单做上下翻滚然后作选择Right&Left让光标作平移，然后定位在特定的数字Back允许编程者返回上级菜单Info显示某参数或操作的更多信息C–编程|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|32底部键HandON–以Hand/Local模式启动VLT，速度用UP和Down键改变OFF–以Hand/Local模式停止电机AutoOn–允许除了面板键的其它信号控制VLTReset–允许操作者手动确认警报C–编程|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|33快捷菜单Q1–我的个性化菜单Q2–快捷设置Q3–功能设置Q5–已完成的更改Q6–日志C–编程|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|34快捷菜单Q1–我的个性化菜单出厂值1.20-21设定值1=0.002.20-93PID比例增益0.503.20-94PID积分时间常数20.00s可加更多的–最多20个参数C–编程|Confidential/PropertyofDanfossDrivesA/S|Tuesday,11February2020|35快捷菜单以前快捷菜单–0-02(RPM)&0-03(N.Ame