桥壳

OP10零件成品OP10夹具OP05工艺OP05-T1-D160面铣刀粗铣面OP05-T3-D50方肩铣刀铣面OP05-T2-D160面铣刀精铣面OP05-T4-D27.6非标飓风钻钻D28底孔OP05-T5-D6.8钻头钻M8底孔OP05-T6-M8丝锥攻丝OP05-T7-D28精镗刀镗孔OP05工艺OP05-T1-D160面铣刀R220.53-8160-15-10C粗铣面vc150n300fz0.2vf600OP05工艺OP05-T2-D160面铣刀R220.53-8160-15-14C精铣面vc200n400fz0.15vf840OP05工艺OP05-T3-D50方肩铣刀R220.69-0050-12-5A铣面vc150n950fz0.1vf480OP05工艺OP05-T4-D27.6非标飓风钻SD59-D27.6-C45-32R7-SP钻D28底孔vc120n1375fz0.1vf137OP05工艺OP05-T5-D6.8钻头SD203A-C45-6.8-25-10R1钻M8底孔vc80n3750fz0.1vf375OP05工艺OP05-T6-M8丝锥E446*M8攻丝vc10n400Fz1.25vf500OP05工艺OP05-T7-D28精镗刀A78010镗孔vc150n1700fz0.1vf170OP25零件成品OP25夹具OP25工艺OP25-T1-D50方肩铣刀铣面OP25-T2-D14.5皇冠钻钻孔X4OP25-T3-M16丝锥攻丝X4OP25工艺OP25-T1-D50方肩铣刀R220.69-0050-12-5A铣面vc150n760fz0.1vf450OP25工艺OP25-T2-D14.5皇冠钻SD100-14.50-K钻孔X4vc65n1400倒角时n700fz0.16vf230OP25工艺OP25-T3-M16丝锥E269*M16X1.5攻丝X4vc15n300Fz1.5vf450OP45夹具OP45零件成品OP45工艺OP45-T1-D80方肩铣刀粗铣面OP45-T2-D80方肩铣刀精铣面OP45-T3-D25飓风钻钻孔X8OP45-T4-D36非标倒角刀倒角X8OP45工艺OP45-T1-D80方肩铣刀R220.69-0080-18-6A粗铣面vc150n600fz0.2vf700OP45工艺OP45-T2-D80方肩铣刀R220.69-0080-18-8A精铣面vc200n800fz0.15vf1000OP45工艺OP45-T3-D25飓风钻SD503-25-75-32R7钻孔X8vc120n1500fz0.15vf220OP45工艺OP45-T4-D36非标倒角刀R218.19-3236.3-SP倒角X8vc100n900fz0.3vf500