BSS安装指南

BSS安装指南彭华2003.6硬件安装安装前需要熟悉SOP，机柜安装要符合规范准备OML表、BSSID，DTE，CICtable，安装文件。内部全尺寸板、半尺寸板插接仔细小心，一定带防静电手环。Cage之间的光纤连接仔细小心，对照安装文件多检查几次。仔细检查MMS2M线头子的质量。BSC板卡XCDR板卡机柜排列架顶加电加电之前测架顶电压。准备一块Dummy板（电压测试板）加电之前将所有的板件拔出来，在全尺寸槽里插入Dummy板，测电压。（－12V、＋12V，±5V。电压测试正常后将板件插入。准备一块1.6.2.0版本的GPROC板。DownCoad第一种方法：从OMC下载1、更新OML表格，添加本BSC的OML。2、在各个XCDR中相应加入用于这个BSC（XCDR）的时隙联接。3、与OMC工程师一起调通OML。4、从OMC下载。DownCoad第二种方法：LanLoad用LanLoad设备通过光纤与BSC的LANX（半尺寸，20槽，7138）板联接，从LanLoad设备将数据导入。DownCoad第三种方法：用NVM板导入（GSR5.0)1、在其他BSC上完成NVM板的数据制作。2、在BSC的20槽插入版本为1.6.2.0的GPROC板。3、在BSC的26槽插入NVM板，BSC重启。4、重启后BSC进入MMI-RAM状态。Down数据在BSC进入MMI-RAM后，使用以下命令：MMI-RAM0115-sysgen_modonCOMMANDACCEPTED:Youmustnowre-initthesitetostartSYSGEN这时将主GPROC复位，使BSC再次重启。重启成功后进入sysgen状态。MMI-RAM0115-WaitingforSystemInitializationtocomplete.....MMI-RAM0115-Initializationcomplete.Proceedwithsysgen.MMI-SYS0115-Down数据在进入sysgen状态后，由于NVM板导入的数据是其他BSC的数据，所以需要将其清除，然后再将本BSC的数据灌入。MMI-SYS0115-clear_databaseCOMMANDACCEPTED此时可以将BSC的数据灌入。BSC调测－MMS环测先ins所有MSI板和GDP板。在DDF架上依次将MMS端口逐一自环，看2M线是否是通的。MMI-RAM0115-state0mms00STATUSINFORMATION:Device:MMS000Administrationstate:UNLOCKEDOperationalstate:BUSYReasoncode:NOREASONTimeoflasttransition:WedJan200:00:501980RelatedDevice/Function:NoneENDOFSTATUSREPORT观察时多观察一段时间BSC调测－主备倒换1、lan倒换，先看当前lan状态MMI-RAM0115-state0lan**DEVICESTATUSINFORMATIONFORLOCATION0:OPERSTATES:D:DisabledE:EnabledB:BusyADMINSTATES:L:LockedU:UnlockedE:EquippedS:ShutdownLastTransitionRelatedDeviceStateReasondd/mmhh:mm:ssFunction-----------------------------------------------------------------------LAN000B-UNOREASON02/0100:05:21NoneLAN100E-UNOREASON02/0100:05:21NoneENDOFSTATUSREPORTBSC调测－主备倒换lan倒换MMI-RAM0115-swap0lanSWFM:Adjustingsaveduserstacksizeto115MMI-RAM0115-state0lan**DEVICESTATUSINFORMATIONFORLOCATION0:OPERSTATES:D:DisabledE:EnabledB:BusyADMINSTATES:L:LockedU:UnlockedE:EquippedS:ShutdownLastTransitionRelatedDeviceStateReasondd/mmhh:mm:ssFunction-----------------------------------------------------------------------LAN000E-UNOREASON02/0100:05:41NoneLAN100B-UNOREASON02/0100:05:41NoneENDOFSTATUSREPORTBSC调测－主备倒换2、KSW倒换，看当前状态MMI-RAM0115-state0ksw**DEVICESTATUSINFORMATIONFORLOCATION0:OPERSTATES:D:DisabledE:EnabledB:BusyADMINSTATES:L:LockedU:UnlockedE:EquippedS:ShutdownLastTransitionRelatedDeviceStateReasondd/mmhh:mm:ssFunction-----------------------------------------------------------------------KSW000B-UNOREASON02/0100:06:30NoneKSW010E-LNOREASON02/0100:06:32NoneKSW100B-UNOREASON02/0100:06:32NoneKSW110E-UNOREASON02/0100:06:32NoneKSW200B-UNOREASON02/0100:06:32NoneKSW210E-UNOREASON02/0100:06:32NoneBSC调测－主备倒换将主用的KSW锁住（l0ksw）。MMI-RAM0115-state0ksw**DEVICESTATUSINFORMATIONFORLOCATION0:OPERSTATES:D:DisabledE:EnabledB:BusyADMINSTATES:L:LockedU:UnlockedE:EquippedS:ShutdownLastTransitionRelatedDeviceStateReasondd/mmhh:mm:ssFunction-----------------------------------------------------------------------KSW000E-LNOREASON02/0100:06:30NoneKSW010B-UNOREASON02/0100:06:32NoneKSW100E-LNOREASON02/0100:06:54NoneKSW110B-UNOREASON02/0100:06:32NoneKSW200E-LNOREASON02/0100:07:01NoneKSW210B-UNOREASON02/0100:06:32NoneENDOFSTATUSREPORT看备用KSW是否能正确变为B-U状态BSC调测－主备倒换3、GCLK倒换，看当前状态MMI-RAM0115-state0gclk**DEVICESTATUSINFORMATIONFORLOCATION0:OPERSTATES:D:DisabledE:EnabledB:BusyADMINSTATES:L:LockedU:UnlockedE:EquippedS:ShutdownLastTransitionRelatedDeviceStateReasondd/mmhh:mm:ssFunction-----------------------------------------------------------------------GCLK000B-UGCLKPhaseLocked02/0100:07:04NoneGCLK100E-UGCLKPhaseLocked02/0100:07:04NoneENDOFSTATUSREPORTBSC调测－主备倒换GCLK主备倒换MMI-RAM0115-swap0gclkGCLKswapmaycausealarmsonotherdevices.Theswapmaytakeapprox.10seconds.Areyousure(y=yes,n=no)?yCOMMANDACCEPTEDMMI-RAM0115-state0gclk**DEVICESTATUSINFORMATIONFORLOCATION0:OPERSTATES:D:DisabledE:EnabledB:BusyADMINSTATES:L:LockedU:UnlockedE:EquippedS:ShutdownLastTransitionRelatedDeviceStateReasondd/mmhh:mm:ssFunction-----------------------------------------------------------------------GCLK000E-UGCLKPhaseLocked02/0100:08:31NoneGCLK100B-UGCLKPhaseLocked02/0100:08:31NoneENDOFSTATUSREPORTBSC调测－主备倒换4、BSP主备倒换BSC有两块GPROC板是bsp，L20的是主用，L24的是备用。MMI-RAM0115-state0bsp**DEVICESTATUSINFORMATIONFORLOCATION0:OPERSTATES:D:DisabledE:EnabledB:BusyADMINSTATES:L:LockedU:UnlockedE:EquippedS:ShutdownLastTransitionRelatedDeviceStateReasondd/mmhh:mm:ssFunction-----------------------------------------------------------------------BSP000B-UNOREASON01/0120:54:46NoneBSP100E-UNOREASON01/0120:54:47NoneENDOFSTATUSREPORTBSC调测－主备倒换BSP倒换将L20的GPROC关掉，bsc重启，等重启成功后看备用的BSP（L24）的状态是否是B-U。MMI-RAM0119-Databasedisplaycommandsaccepted.MMI-RAM0119-Initializationcomplete.Allcommandsaccepted.MMI-RAM0119-state0bsp**DEVICESTATUSINFORMATIONFORLOCATION0:OPERSTATES:D:DisabledE:EnabledB:BusyADMINSTATES:L:LockedU:UnlockedE:EquippedS:ShutdownLastTransitionRelatedDeviceStateReasondd/mmhh:mm:ssFunction-----------------------------------------------------------------------BSP000D-UGPROCNotOnLAN02/0100:24:58NoneBSP100B-UNOREASON02/0100:23:36NoneENDOFSTATUSREPORTBSC调测—CIC测试在测试以