功能块编写

Date:2020/2/24File:SSP1_07C.1SIMATICS7NortheasternUniversityLihongru块的编辑Date:2020/2/24File:SSP1_07C.2SIMATICS7NortheasternUniversityLihongruSTEP7编程语言AI0.0AI0.1=Q8.0STL&Q8.0=I0.0I0.1FBDI0.0I0.1Q8.0LADDate:2020/2/24File:SSP1_07C.3SIMATICS7NortheasternUniversityLihongru启动LAD/STL/FBD编辑器2xDate:2020/2/24File:SSP1_07C.4SIMATICS7NortheasternUniversityLihongruLAD/STL/FBD编辑器的组成Browser声明表代码区Date:2020/2/24File:SSP1_07C.5SIMATICS7NortheasternUniversityLihongru选择编程语言Date:2020/2/24File:SSP1_07C.6SIMATICS7NortheasternUniversityLihongru用LAD/FBD编程Date:2020/2/24File:SSP1_07C.7SIMATICS7NortheasternUniversityLihongru用STL编程Date:2020/2/24File:SSP1_07C.8SIMATICS7NortheasternUniversityLihongru块的保存带有块名称的当前项目路径Date:2020/2/24File:SSP1_07C.9SIMATICS7NortheasternUniversityLihongru在OB1中调用块Date:2020/2/24File:SSP1_07C.10SIMATICS7NortheasternUniversityLihongru下载块到PLCDate:2020/2/24File:SSP1_07C.11SIMATICS7NortheasternUniversityLihongru简单程序的调试Date:2020/2/24File:SSP1_07C.12SIMATICS7NortheasternUniversityLihongru下载和保存修改的块打开离线打开在线保存下载(Q8.0)Date:2020/2/24File:SSP1_07C.13SIMATICS7NortheasternUniversityLihongru助记符德语英语(国际)…选择编辑语言LAD/STL/FBD在打开程序块或程序前...练习7.1：选择助记符Date:2020/2/24File:SSP1_07C.14SIMATICS7NortheasternUniversityLihongru练习7.2:打开并编辑FC1Date:2020/2/24File:SSP1_07C.15SIMATICS7NortheasternUniversityLihongru在打开一个块后...选择需要使用的编程语言练习7.3：变换编程语言•梯形图(LAD)•语句表(STL)•功能块图(FBD)Date:2020/2/24File:SSP1_07C.16SIMATICS7NortheasternUniversityLihongru选择菜单选项File-Save不修改名称保存块或文件..…或点击练习7.4：保存FC1利用File-SaveAs以不同的名字保存块或存放在不同的地方Date:2020/2/24File:SSP1_07C.17SIMATICS7NortheasternUniversityLihongru练习7.5：下载块到PLC或点击下载图标把一个块传到CPU...Date:2020/2/24File:SSP1_07C.18SIMATICS7NortheasternUniversityLihongru练习7.6：在OB1中调用FC1Date:2020/2/24File:SSP1_07C.19SIMATICS7NortheasternUniversityLihongru练习7.7：测试FC1(用LAD)信号状态检查结果输入I0.0I0.1I0.0I0.1I0.0I0.1I0.0I0.10011100101101100I0.0I0.1Q4.0I0.0I0.1Q4.0I0.0I0.1Q4.0I0.0I0.1Q4.0Date:2020/2/24File:SSP1_07C.20SIMATICS7NortheasternUniversityLihongru练习7.8：在FC1块中扩展程序Date:2020/2/24File:SSP1_07C.21SIMATICS7NortheasternUniversityLihongru编辑器用户设置：“Editor”标签Date:2020/2/24File:SSP1_07C.22SIMATICS7NortheasternUniversityLihongru编辑器用户设置：“STL”标签Date:2020/2/24File:SSP1_07C.23SIMATICS7NortheasternUniversityLihongru编辑器用户设置：“LAD/FBD”标签Date:2020/2/24File:SSP1_07C.24SIMATICS7NortheasternUniversityLihongru编辑器用户设置：“CreateBlock”标签Date:2020/2/24File:SSP1_07C.25SIMATICS7NortheasternUniversityLihongru编辑器用户设置：“SourceFiles”标签Date:2020/2/24File:SSP1_07C.26SIMATICS7NortheasternUniversityLihongru编辑器用户设置：“SymbolSelection”标签