HT海天注塑机技术参数

型号参数螺杆直径mm343640343640343640404548理论注射容量cm3111124153131147181131147181253320364注射重量PSg101113139119134165119134165230291331注射压力Mpa206183149206183149206183149202159140注射行程mm螺杆转速r/min料筒加热功率KW锁模力KN拉杆内间距(水平×垂直)mm允许最大模具厚度mm允许最小模具厚度mm移模行程mm移模开距(最大)mm液压顶出行程mm液压顶出力KN液压顶出杆数量PC油泵电动机功率KW油箱容积l机器尺寸(长×宽×高)m机器重量t最小模具尺寸(长×宽)mm320×3202102404.7×1.3×1.855.4×1.45×2.05HTF海天注塑机技术参数3.45280×2803333551318.5340420750920100140400×400455×4554105001601800~2150~2305.79.311001600160×2B160×2C144201110×1A110×1B110×1C160×2A3.223.45240×240255×25511132002004.3×1.25×1.84.5×1.25×1.9100100333355150150310310670670800860365×365360×36036036086×2C1221440~2200~2405.75.7单位80×A80×B80×C86×2A86×2B型号参数螺杆直径mm455055606570657075708084理论注射容量cm3334412499727853989106812391423142418602050注射重量PSg30437545466277690097211271295129616931866注射压力Mpa210170141213182157208180156204156141注射行程mm螺杆转速r/min料筒加热功率KW锁模力KN拉杆内间距(水平×垂直)mm允许最大模具厚度mm允许最小模具厚度mm移模行程mm移模开距(最大)mm液压顶出行程mm液压顶出力KN液压顶出杆数量PC油泵电动机功率KW油箱容积l机器尺寸(长×宽×高)m机器重量t最小模具尺寸(长×宽)mmHTF海天注塑机技术参数HTF海天注塑机技术参数1519550×550550×550374592210507.6×2.1×2.58.2×2.3×3.216020011011013132503306607401370152036004500710×710780×7807107803223700~1800~16019.6523.85360×2A360×2B360×2C450×2A450×2B450×2C350×350460×4603005805.2×1.6×2.16.9×2.0×2.4611.5626291318.5304706609801260130160510×510660×6605106602002500~1500~16012.4517.2520003000单位200×A200×B200×C210257300×A300×B300×C型号参数螺杆直径mm75809090100110120110120130140理论注射容量cm317491991251927993456418149765227622073008467注射重量PSg15921812229225473145380545284757566066437705注射压力Mpa205180142228184152128205172147126注射行程mm螺杆转速r/min料筒加热功率KW锁模力KN拉杆内间距(水平×垂直)mm允许最大模具厚度mm允许最小模具厚度mm移模行程mm移模开距(最大)mm液压顶出行程mm液压顶出力KN液压顶出杆数量PC油泵电动机功率KW油箱容积l机器尺寸(长×宽×高)m机器重量t最小模具尺寸(长×宽)mm型号870×8702152155+55240055012502500320690×69018621196026013.1×3.1×4.165780×1C0~1100~9085.25125001250×12501250×2A1250×2B1250×2C5501250780×1D4401250×2D780×1A780×1B90W1×A37+371778单位120W1×A120W1×B120W1×C90W1×B90W1×C15817HTF海天注塑机技术参数570×5705512508.7×2.3×2.73010.1×2.6×3.845820×8208203508201640200单位530×A530×B530×C3970~12058.457800400980980×98098041.855300参数螺杆直径mm364045理论注射容量cm3173214270注射重量PSg157195246注射压力Mpa210171135注射行程mm螺杆转速r/min料筒加热功率KW锁模力KN拉杆内间距(水平×垂直)mm允许最大模具厚度mm允许最小模具厚度mm移模行程mm移模开距(最大)mm液压顶出行程mm液压顶出力KN液压顶出杆数量PC油泵电动机功率KW油箱容积l机器尺寸(长×宽×高)m机器重量t最小模具尺寸(长×宽)mm模≥150－160mmum模具具＞160－250mmum平行度厚＞250－400mmum度＞400－430mmum60801004.6290×29050132804.83×1.26×1.9612033515036081012410×41045017090W1×A0~1909.75单位120W1×A120W1×B120W1×C90W1×B90W1×C