PACK材料检验规范

PACK原物料检验规范文件编号版本号：发行号文件管控章核准：审核：制定：会签：※本文件之著作权属威力能电池科技（深圳）有限公司，非经允许不得翻印※POWERSOURUCEENGERGYBATTERYTECHNOLOGY(SHENZHEN)CO.,LTD.威力能电池科技(深圳)有限公司文件名称文件编号PACK原物料检验规范YJG-824-02页次1of29版本0101适用范围：单体NI-MH电芯序号检验项目标准要求抽样方案检测方法检验设备相关表单1外观电池周身无机械损伤，外壳和正负极极端无锈蚀，无电解液IL=IIAQL=2.5距离电池30cm处肉眼目视无『-选分协作申请单』『-电芯检测批报表』『原物料检验记录』『原物料检验报告』『不合格品处置单』2壳身喷码内容符合订单要求,无掉字、模糊不清且不易擦去IL=S-3AQL=1.0目测，核对码样是否与订单要求一致无3尺寸符合附表〈一〉NI-MH电池规格书用卡尺分别夹持所测电芯相关部位以电芯不掉下为准，所测数据即为电芯尺寸数据数显卡尺4开路电压≥1.27v且不低于批电池平均电压-10mvIL=II低压：AQL=0.65短路：AQL=0.25将万用表调至20V电压档，并用正、负表笔分别接触被测电芯正、负极，所得数据即为该电芯的开路电压数字万用表5荷电态内阻符合附表〈一〉NI-MH电池规格书IL=IIAQL=0.25将电芯放入内阻测试夹具中接触良好，所测得数据即为该电芯内阻（测量前先将内阻仪预热30分钟）内阻测试仪6容量符合附表〈一〉NI-MH电池规格书生产全检1.填写一式两份『-选分协作申请单』，注明相关检验数据及要求，交分容车间，并将电池转入分容车间分容；2.待容量全检后由分容车间填写『＿电芯检测批报表』交原物料组；3.IQC根据其容量结果判定此批电芯之质量二次电池检测装置备注：1.当电池开路电压低于批平均电压但大于0.5V时为低压不良，低于0.5V时为短路2.电池的不良仅考虑最低AQL对应的不良；每批若有1PCS以上的电池发生爆炸，则整批做退货处理。※本文件之著作权属威力能电池科技（深圳）有限公司，非经允许不得翻印※POWERSOURUCEENGERGYBATTERYTECHNOLOGY(SHENZHEN)CO.,LTD.威力能电池科技(深圳)有限公司文件名称文件编号PACK原物料检验规范YJG-824-02页次2of29版本0101附表〈一〉NI-MH电池规格书序号型号规格荷电态开路电压(V)最小容量(mAh)尺寸(mm)内阻(mΩ)电池容量充放电检测制度裸电电芯包装电芯总高度0/-1.00罐身头径＋0/-0.50罐身直径＋0/-0.50罐身头径＋0/-0.50罐身直径＋0/-0.50129AAA3001.2730010.210.210.510.529≤300.2C5A充7.0h，0.2C5A放1.0V243AAA6001.2760010.210.210.510.543≤301.0C5A充1.2h，1.0C5A放1.0V343AAA6501.2765010.210.210.510.543≤301.0C5A充1.2h，1.0C5A放1.0V443AAA尖6001.2760010.210.210.510.544.5≤301.0C5A充1.2h，1.0C5A放1.0V543AAA尖6501.2763010.210.210.510.544.5≤301.0C5A充1.2h，1.0C5A放1.0V644AAA7001.2768010.210.210.510.544≤300.5C5A充2.4h，1.0C5A放1.0V744AAA尖7001.2768010.210.210.510.544.5≤300.5C5A充2.4h，1.0C5A放1.0V844AAA尖7501.2773010.210.210.510.544.5≤300.5C5A充2.4h，1.0C5A放1.0V944AAA尖8001.2778010.210.210.510.544.5≤300.5C5A充2.4h，1.0C5A放1.0V1050AAA7501.2773010.210.210.510.550≤301.0C5A充1.2h，1.0C5A放1.0V1128AA6501.2765014.314.314.514.528≤301.0C5A充1.2h，1.0C5A放1.0V1243AA12001.27120014.314.314.514.543≤251.0C5A充1.2h，1.0C5A放1.0V1348AA14001.27140014.314.314.514.548≤251.0C5A充1.2h，1.0C5A放1.0V1449AA14001.27140014.314.314.514.549≤251.0C5A充1.2h，1.0C5A放1.0V1549AA15001.27150014.314.314.514.549≤251.0C5A充1.2h，1.0C5A放1.0V1649AA16001.27160014.314.314.514.549≤251.0C5A充1.2h，1.0C5A放1.0V1749AA17001.27165014.314.314.514.549≤250.5C5A充2.4h，0.5C5A放1.0V1849AA18001.27175014.314.314.514.549≤250.5C5A充2.4h，0.5C5A放1.0V1950AA19001.27185014.314.314.514.550≤250.5C5A充2.4h，0.5C5A放1.0V2050AA20001.27195014.314.314.514.550≤250.5C5A充2.3h，0.5C5A放1.0V2150AA21001.27205014.314.314.514.550≤250.5C5A充2.3h，0.5C5A放1.0V2250AA22001.27215014.314.314.514.550≤250.5C5A充2.3h，0.5C5A放1.0V2350AA尖13001.27130014.314.314.514.550.5≤251.0C5A充1.2h，1.0C5A放1.0V2450AA尖14001.27140014.314.314.514.550.5≤251.0C5A充1.2h，1.0C5A放1.0V2550AA尖15001.27150014.314.314.514.550.5≤251.0C5A充1.2h，1.0C5A放1.0V※本文件之著作权属威力能电池科技（深圳）有限公司，非经允许不得翻印※POWERSOURUCEENGERGYBATTERYTECHNOLOGY(SHENZHEN)CO.,LTD.威力能电池科技(深圳)有限公司文件名称文件编号PACK原物料检验规范YJG-824-02页次3of29版本0101续附表〈一〉NI-MH电池规格书序号型号规格荷电态开路电压(V)最小容量(mAh)尺寸(mm)内阻(mΩ)电池容量充放电检测制度裸电电芯包装电芯总高度0/-1.00罐身头径＋0/-0.50罐身直径＋0/-0.50罐身头径＋0/-0.50罐身直径＋0/-0.502650AA尖16001.27160014.314.314.514.550.5≤251.0C5A充1.2h，1.0C5A放1.0V2750AA尖17001.27165014.314.314.514.550.5≤251.0C5A充1.2h，1.0C5A放1.0V2850AA尖18001.27175014.314.314.514.550.5≤250.5C5A充2.4h，0.5C5A放1.0V2950AA尖19001.27185014.314.314.514.550.5≤250.5C5A充2.4h，0.5C5A放1.0V3050AA尖20001.27195014.314.314.514.550.5≤250.5C5A充2.3h，0.5C5A放1.0V3150AA尖21001.27205014.314.314.514.550.5≤250.5C5A充2.3h，0.5C5A放1.0V3250AA尖22001.27215014.314.314.514.550.5≤250.5C5A充2.3h，0.5C5A放1.0V3350AA尖23001.27225014.314.314.514.550.5≤250.5C5A充2.3h，0.5C5A放1.0V3428A10001.27100016.716.717.017.028≤250.5C5A充2.4h，1.0C5A放1.0V3543A18001.27180016.716.717.017.043≤250.5C5A充2.4h，0.5C5A放1.0V3643A19001.27190016.716.717.017.043≤250.5C5A充2.4h，0.5C5A放1.0V3750A21001.27210016.716.717.017.050≤200.5C5A充2.4h，0.5C5A放1.0V3850A22001.27220016.716.717.017.050≤200.5C5A充2.4h，0.5C5A放1.0V3967A30001.27300016.716.717.017.067≤200.5C5A充2.4h，0.5C5A放1.0V40SC30001.27300022.522.523.023.043≤150.5C5A充2.4h，0.5C5A放1.0V41SC33001.27325022.522.523.023.043≤150.5C5A充2.4h，0.5C5A放1.0V42C36001.27360025.425.425.825.848.5≤150.4C5A充3.5h，0.5C5A放1.0V43C40001.27400025.425.425.825.848.5≤150.4C5A充3.5h，0.4C5A放1.0V44C尖36001.27360025.425.425.825.850.0≤150.4C5A充3.5h，0.5C5A放1.0V45C尖40001.27400025.425.425.825.850.0≤150.4C5A充3.5h，0.4C5A放1.0V46D76001.27760032.032.032.532.558.5≤100.2C5A充7.0h，0.2C5A放1.0V47D80001.27800032.032.032.532.558.5≤100.2C5A充7.0h，0.2C5A放1.0V48D尖76001.27760032.032.032.532.561.0≤100.2C5A充7.0h，0.2C5A放1.0V49D尖80001.27800032.032.032.532.561.0≤100.2C5A充7.0h，0.2C5A放1.0V※本文件之著作权属威力能电池科技（深圳）有限公司，非经允许不得翻印※POWERSOURUCEENGERGYBATTERYTECHNOLOGY(SHENZHEN)CO.,LTD.威力能电池科技(深圳)有限公司文件名称文件编号PACK原物料检验规范YJG-824-02页次4of29版本0101续附表〈一〉NI-MH电池规格书序号型号规格荷电态开路电压(V)最小容量(mAh)尺寸(mm)内阻(mΩ)电池容量充放电检测制度裸电电芯包装电芯总高度0/-1.00罐身头径＋0/-0.50罐身直径＋0/-0.50罐身头径＋0/-0.50罐身直径＋0/-0.5050AIU1.2711006.0-0.5*16.8-0.7*67.0-0.5(厚×宽×长)≤250.5C5A充1.2h，0.5C5A放1.0V52BIU1.277006.0-0.5*16.8-0.7*47.8-0.5(厚×宽×长)≤251.0C5A充1.2h，1.0C5A放1.0V53BIU1.277506.0-0.5*16.8-0.7*47.8-0.5(厚×宽×长)≤251.0C5A充1.2h，1.0C5A放1.0V54CIUⅠ1.275506.0-0.5*16.8-0.7*35.5-0.5(厚×宽×长)≤251.0C5A