螺丝扭力一览表

编号日期2018/6/13版次1.0页次1/5项次K3号螺丝规格规格型号扭力范围kgf.cm±0.5备注11.13.0101.0000013*8十字圆头机牙螺丝（镀锌）W-PMA-013.521.13.0101.0000023*6十字圆头机牙螺丝（不锈钢）W-PMA-022.531.13.0101.0000034*10十字圆头机牙螺丝（镀锌）W-PMB-014.541.13.0101.0000044*12十字圆头机牙螺丝（镀锌）W-PMB-02551.13.0101.0000054*6十字圆头机牙螺丝（不锈钢304）W-PMB-03461.13.0101.0000064*20十字圆头机牙螺丝（不锈钢304）W-PMB-044.571.13.0101.0000081.6*6十字圆头尖尾自攻螺丝（镀锌）W-PAA-010.781.13.0101.0000092*10十字圆头尖尾自攻螺丝（镀锌）W-PAB-01291.13.0101.0000102.5*8十字圆头尖尾自攻螺丝（镀锌）W-PAC-012.5101.13.0101.0000112.6*6十字圆头尖尾自攻螺丝（镀锌）PAW-PAD-013111.13.0101.0000122.6*10十字圆头尖尾自攻螺丝（镀锌）W-PAD-023121.13.0101.0000133*8十字圆头尖尾自攻螺丝（镀锌）W-PAE-013.5131.13.0101.0000143*8十字小盘头尖尾自攻螺丝（不锈钢）W-PAE-023.5141.13.0101.0000153*8十字沉头尖尾自攻螺丝（镀锌）W-PAE-033.5151.13.0101.0000163*10十字圆头尖尾自攻螺丝（镀锌）W-PAE-044161.13.0101.0000173*16十字圆头尖尾自攻螺丝（镀锌）W-PAE-054171.13.0101.0000183*25十字圆头尖尾自攻螺丝（镀锌）W-PAE-064181.13.0101.0000194*10十字圆头尖尾自攻螺丝（镀锌）W-PAF-014.5191.13.0101.0000204*12十字圆头尖尾自攻螺丝（镀锌）W-PAF-024.5201.13.0101.0000214*16十字圆头尖尾自攻螺丝（镀锌）W-PAF-035211.13.0101.0000224*20十字圆头尖尾自攻螺丝（不锈铁）W-PAF-045.5221.13.0101.0000234.8*13十字圆头尖尾自攻螺丝（镀锌）W-PAG-014.5螺丝扭力一览表1、本扭力标准适用于一般规格的设计；2、新产品量产前，PE需对螺丝按此标准测试，如有不符合项做出相应调整，确定后加入SOP中去。编号日期2018/6/13版次1.0页次2/5项次K3号螺丝规格规格型号扭力范围kgf.cm±0.5备注231.13.0101.0000244*8十字大扁头尖尾自攻螺丝（镀锌）W-TAA-014241.13.0101.0000254*8十字大扁头尖尾自攻螺丝（不锈钢304）W-TAA-024251.13.0101.0000266*20无槽圆头机牙螺丝（不锈钢304）W-SCR-014261.13.0101.0000273*12十字圆头机牙螺丝（镀锌）W-PMA-034.5271.13.0101.0000283*6十字圆头尖尾自攻螺丝（镀锌）W-PAE-072.5281.13.0101.0000293*16十字圆头机牙螺丝（镀锌）W-PMA-044291.13.0101.0000304*16十字圆头机牙螺丝（镀锌）W-PMB-055301.13.0101.0000314*10十字沉头机牙螺丝（不锈钢）W-PMB-064.5311.13.0101.0000334*25十字圆头尖尾自攻螺丝（不锈钢）W-PAF-055321.13.0101.0000343*10十字圆头机牙螺丝（镀锌）W-PMA-054331.13.0101.0000353*12十字圆头尖尾自攻螺丝（镀锌）W-PAE-084341.13.0101.0000362.8*35十字圆头尖尾自攻螺丝（不锈钢）PAW-PAH-013.5351.13.0101.0000372.5*6十字圆头尖尾自攻螺丝（不锈钢）PAW-PAC-022361.13.0101.0000382.5*10十字圆头尖尾自攻螺丝（不锈钢）W-PAC-032.5371.13.0101.0000404*8十字沉头机牙螺丝（不锈钢）W-PMB-074381.13.0101.0000411.7*6十字平头尖尾自攻螺丝（镀锌）W-PAA-020.7391.13.0101.0000422*5十字圆头尖尾自攻螺丝（铁镀锌）PAW-PAB-022401.13.0101.0000434*25十字圆头机牙螺丝（不锈钢）PMW-PMB-085411.13.0101.0000445*35十字圆头尖尾自攻螺丝（镀锌）W-PAG-025.5421.13.0101.0000454*6十字沉头机牙螺丝（不锈钢）W-PMB-093.5431.13.0101.0000465*25内六角沉头机牙螺丝（不锈钢）W-PMB-104.5441.13.0101.0000475*16十字圆头尖尾自攻螺丝（电镀）W-PAG-035.5螺丝扭力一览表1、本扭力标准适用于一般规格的设计；2、新产品量产前，PE需对螺丝按此标准测试，如果不符合项做出相应调整，确定后加入SOP中去。编号日期2018/6/13版次1.0页次3/5项次K3号螺丝规格规格型号扭力范围kgf.cm±0.5备注451.13.0101.0000485*18十字圆头尖尾自攻螺丝（电镀）W-PAG-045.5461.13.0101.0000493*16十字沉头机牙螺丝（不锈钢）W-PMA-074471.13.0101.0000504.20内六角无头机牙螺丝W-PMB-114481.13.0101.0000513*25十字圆头机牙螺丝（不锈钢）W-PMA-084491.13.0101.0000532*6十字圆头机牙螺丝（不锈钢）W-PMD-012501.13.0101.0000542.5*6十字圆头机牙螺丝（不锈钢）W-PMD-022511.13.0101.0000555*30十字圆头机牙螺丝（不锈钢）W-PMC-045521.13.0101.0000564*40十字圆头机牙螺丝（不锈钢）W-PMB-125531.13.0101.0000576*30无槽圆头机牙螺丝（不锈钢304）W-SCR-025541.13.0101.0000585*35十字圆头尖尾自攻螺丝（环保）W-PAE-095.5551.13.0101.0000613*20十字圆头机牙螺丝（不锈钢）W-PMA-103.5561.13.0101.0000673*8十字圆头机牙螺丝（不锈钢）W-PMA-133571.13.0101.0000682.6*10十字圆头尖尾自攻螺丝（不锈钢）W-PAD-032.5581.13.0101.0000693*12十字圆头机牙螺丝（不锈钢）W-PMA-143.5591.13.0101.0000704*10十字圆头机牙螺丝（不锈钢）W-PMB-153.5601.13.0101.0000714*30十字圆头机牙螺丝（镀锌）W-PMB-164611.13.0101.0000724*50十字沉头机牙螺丝（镀锌）W-PMB-175621.13.0101.0000734*8十字圆头机牙螺丝（不锈钢）W-PMB-184631.13.0101.0000744*12十字内六角机牙螺丝（不锈钢）W-PMB-194641.13.0101.0000751.6*4十字圆头尖尾自攻螺丝（镀锌）W-PAA-030.7651.13.0101.0000762*3十字圆头尖尾自攻螺丝（不锈铁）W-PAB-031.5661.13.0101.0000772*6十字圆头尖尾自攻螺丝（镀锌）W-PAB-042螺丝扭力一览表1、本扭力标准适用于一般规格的设计；2、新产品量产前，PE需对螺丝按此标准测试，如果不符合项做出相应调整，确定后加入SOP中去。编号日期2018/6/13版次1.0页次4/5项次K3号螺丝规格规格型号扭力范围kgf.cm±0.5备注671.13.0101.0000782*8十字圆头尖尾自攻螺丝（镀锌）W-PAB-052681.13.0101.0000793*5罗纹压铆钉（黄铜）W-NUT-32691.13.0101.0000804*30十字沉头机牙螺丝W-PMB-204701.13.0101.0000814*12十字圆头机牙螺丝（不锈钢）W-PMB-213.5711.13.0101.0000824*10内六角圆头机牙螺丝（不锈钢）W-PMC-064721.13.0101.0000833*6十字圆头尖尾自攻螺丝（不锈钢304）W-PAE-112.5731.13.0101.0000843*8十字圆头尖尾自攻螺丝（不锈钢304）W-PAE-122.5741.13.0101.0000854*10十字小盘头尖尾自攻螺丝（不锈钢304）W-PAF-074751.13.0101.0000873*16十字圆头尖尾自攻螺丝（不锈钢304）PAW-PAE-153.5761.13.0101.0000882.5*8十字沉头机牙螺丝（不锈钢）W-PMB-222771.13.0101.0000893.5*25十字沉头尖尾自攻螺丝（304不锈钢）直径3.5*253.5781.13.0101.0000902*4十字圆头平尾自攻螺丝（镀镍）W-PAB-061.5791.13.0101.0000912*3十字圆头带垫片平尾自攻螺丝（镀镍）W-PAB-071801.13.0101.0000923*10十字圆头平尾自攻螺丝（不锈钢）W-PMB-232.5811.13.0101.0000934*12十字圆头平尾自攻螺丝（不锈钢）W-PMB-243821.13.0101.0000944*8十字圆头平尾自攻螺丝（不锈钢）W-PMB-253831.13.0101.0000952*5十字圆头尖尾自攻螺丝（铁镀镍）W-PAB-081.5841.13.0101.0000964*25十字圆头机牙螺丝（镀锌）W-PMB-234851.13.0101.0000974*6十字沉头机牙螺丝（不锈钢）W-PMB-263861.13.0101.0000983*18内六角无头机牙螺丝（发黑）W-PMA-173871.13.0101.0000991.4*6十字沉头尖尾自攻螺丝（铁镀镍）W-PAA-040.7881.13.0101.0001004*10十字圆头平尾自攻螺丝（不锈钢）W-PMB-274螺丝扭力一览表1、本扭力标准适用于一般规格的设计；2、新产品量产前，PE需对螺丝按此标准测试，如果不符合项做出相应调整，确定后加入SOP中去。编号日期2018/6/13版次1.0页次5/5项次K3号螺丝规格规格型号扭力范围kgf.cm±0.5备注891.13.0101.0001014*45内六角圆头机牙螺丝（不锈钢）W-PMB-285901.13.0101.0001023.9*16十字圆头尖尾自攻螺丝（不锈钢）W-PAF-083.5911.13.0101.0001032.9*25十字圆头尖尾自攻螺丝（不锈钢）W-PAE-133921.13.0101.0001043.5*38十字圆头尖尾自攻螺丝（不锈钢）PAW-PAF-093.5931.13.0101.0001053.5*25十字平头尖尾自攻螺丝（不锈钢）W-PAF-103.5941.13.0101.0001063*5十字圆头平尾自攻螺丝（镀锌）W-PMB-292.5951.13.0101.0001071.4*5十字沉头尖尾自攻螺丝（铁镀镍）W-PAA-050.7961.13.0101.0001083*6十字沉头机牙螺丝（不锈钢）W-PMA-192.5971.13.0101.0001093*12十字沉头尖尾自攻螺丝（不锈钢