grasshopper电池组翻译

Vector改变Field仿射Scale-------------------------------------------------------------Scaleanobjectuniformlyinalldirections.Inputparameters:-------------------------------------------------------------Inputparameters:G(Geometry)BasegeometryC(Point)CenterofscalingF(Number)ScalingfactorOutputparameters:G(Geometry)ScaledgeometryX(Transform)Transformationdata秤-------------------------------------------------------------在所有方向均匀地缩放对象。-------------------------------------------------------------输入参数：G（几何）基本几何C（点）缩放中心F（数）缩放系数输出参数：G（几何）缩放几何X（变换）转换数据ScaleNU-------------------------------------------------------------Scaleanobjectwithnon-uniformfactors.-------------------------------------------------------------Inputparameters:G(Geometry)BasegeometryP(Plane)BaseplaneX(Number)Scalingfactorin{x}directionY(Number)Scalingfactorin{y}directionZ(Number)Scalingfactorin{z}directionOutputparameters:G(Geometry)ScaledgeometryX(Transform)Transformationdata规模NU-------------------------------------------------------------缩放对象具有非均匀的因素。-------------------------------------------------------------输入参数：G（几何）基本几何P（平面）基面X（编号）在{X}方向缩放系数Y（数量）在{Y}方向缩放系数Z（数量）在{Z}方向缩放系数输出参数：G（几何）缩放几何X（变换）转换数据Shear-------------------------------------------------------------Shearanobjectbasedonashearingvector.-------------------------------------------------------------Inputparameters:G(Geometry)BasegeometryP(Plane)BaseplaneG(Point)ReferencepointT(Point)TargetpointOutputparameters:G(Geometry)ShearedgeometryX(Transform)Transformatiodata剪断-------------------------------------------------------------剪切基于剪切向量的对象。-------------------------------------------------------------输入参数：G（几何）基本几何P（平面）基面G（点）参照点T（点）目标点输出参数：G（几何）剪切几何X（变换）变换的数据ShearAngle-------------------------------------------------------------Shearanobjectbasedontiltangles.-------------------------------------------------------------Inputparameters:G(Geometry)BasegeometryP(Plane)BaseplaneAx(Number)Rotationaround{x}axisinradiansAy(Number)Rotationaround{y}axisinradiansOutputparameters:G(Geometry)ShearedgeometryX(Transform)Transformationdata剪切角-------------------------------------------------------------剪切根据倾斜角度的对象。-------------------------------------------------------------输入参数：G（几何）基本几何P（平面）基面AX（数）左右旋转{X}轴弧度唉（数）弧度左右旋转{Y}轴输出参数：G（几何）剪切几何X（变换）转换数据BoxMapping-------------------------------------------------------------Transformgeometryfromoneboxintoanother.-------------------------------------------------------------Inputparameters:G(Geometry)BasegeometryS(Box)BoxtomapfromT(Box)BoxtomapintoOutputparameters:G(Geometry)MappedgeometryX(Transform)Transformationdata箱映射-------------------------------------------------------------从一个盒子形状变换成另一种。-------------------------------------------------------------输入参数：G（几何）基本几何S（盒）然后就可以从图T（盒）框映射成输出参数：G（几何）映射几何X（变换）转换数据OrientDirection-------------------------------------------------------------Orientanobjectusingdirectionalconstraintsonly.-------------------------------------------------------------Inputparameters:G(Geometry)BasegeometrypA(Point)ReferencepointdA(Vector)ReferencedirectionpB(Point)TargetpointdB(Vector)TargetdirectionOutputparameters:G(Geometry)ReorientedgeometryX(Transform)Transformationdata取向方向-------------------------------------------------------------取向只使用定向约束的对象。-------------------------------------------------------------输入参数：G（几何）基本几何PA（点）参照点达（矢量）参考方向PB（点）目标点分贝（向量）目标方向输出参数：G（几何）重新定位几何X（变换）转换数据Project-------------------------------------------------------------Projectanobjectontoaplane.-------------------------------------------------------------Inputparameters:G(GenericData)GeometrytoprojectP(Plane)ProjectionplaneOutputparameters:G(GenericData)ProjectedgeometryX(Transform)Transformationdata工程-------------------------------------------------------------投射对象到一个平面上。-------------------------------------------------------------输入参数：G（通用数据）几何项目P（平面）投影面输出参数：G（通用数据）投影几何X（变换）转换数据ProjectAlong-------------------------------------------------------------Projectanobjectontoaplanealongadirection.-------------------------------------------------------------Inputparameters:G(GenericData)GeometrytoprojectP(Plane)ProjectionplaneD(Vector)ProjectiondirectionOutputparameters:G(GenericData)ProjectedgeometryX(Transform)Transformationdata项目沿-------------------------------------------------------------投影到物体沿着一个方向的平面。-------------------------------------------------------------输入参数：G（通用数据）几何项目P（平面）投影面D（矢量）投影方向输出参数：G（通用数据）投影几何X（变换）转换数据RectangleMapping-------------------------------------------------------------Transformgeometryfromonerectangleintoanother.-------------------------------------------------------------Inputparameters:G(Geometry)BasegeometryS(Rectangle)RectangletomapfromT(Rectangle)RectangletomapintoOutputparameters:G(Geometry)MappedgeometryX(Transform)Transformationdata矩形制图-------------------------------------------------------------从一个矩形几何变换到另一个。-------------------------------------------------------------输入参数：G（几何）基本几何S（矩形）矩形从图T（矩形）矩形映射成输出参数：G（几何）映射几何X（变换）转换数据TriangleMapping