JBT 9163.10-1999 压帽式剃珩齿心轴 尺寸

ICS25.080.01J52JB/T9163.10－1999压帽式剃珩齿心轴尺寸Mandrelswithpress–capforgearshavingmachineorgearhoningmachine—Dimensions1999-05-20发布2000-01-01实施国家机械工业局发布11范围本标准规定了压帽式剃珩齿心轴的型式和尺寸，适用于加工定位直径为12～80mm的齿轮。2型式和尺寸型式和尺寸按下图和表的规定。表mm国家机械工业局1999-05-20批准中华人民共和国机械行业标准压帽式剃珩齿心轴尺寸Mandrelswithpress–capforgearshavingmachineorgearhoningmachine—DimensionsJB/T9163.10－1999代替ZBJ52002.10－872000-01-01实施JB/T9163.10－19992d基本尺寸极限偏差h6ll1φLmax35821250973582135097358214551023582155510240871665112408717651124088180011.0-75123408819751234088207532.17612350102218013250102228013250102238013250102248013255107259014255107269014260112289514760127300013.0-9538.458162JB/T9163.10－19993表(续)mmd基本尺寸极限偏差h6ll1φLmax601273295162601273495162701403611018070140381101807014040110180901604212019090160451302009016046130200901624814521790162500016.0-145217901625214521710017553150225100175561502251101856016524012019062175250120195630019.0-17553.458250JB/T9163.10－19994表（完）mmd基本尺寸极限偏差h6ll1φLmax12019567175250130205711852601302057218526013020575190265140215800019.0-20053.4582753标记标记示例：d=20mm、l=75mm的压帽式剃珩齿心轴的标记：心轴20×75JB/T9163.10—1999JB/T9163.10－19995附录A本附录所列Ⅰ、Ⅱ两种心轴直径尺寸为参考数值，是根据工件定位孔在工序间的加工余量确定的，主要供工序间加工使用。mm工艺余量心轴直径尺寸工艺余量心轴直径尺寸基本尺寸dⅠⅡ极限偏差h6基本尺寸dⅠⅡ极限偏差h61211.8011.603635.8035.601312.8012.603837.8037.601413.8013.604039.8039.601514.8014.604241.8041.601615.8015.604544.8044.601716.8016.604645.8045.601817.8017.600011.0-4847.8047.601918.8018.605049.8049.500016.0-2019.8019.605251.8051.502120.8020.605352.8052.502221.8021.605655.8055.502322.8022.606059.8059.502423.8023.606261.8061.502524.8024.606362.8062.502625.8025.606766.8066.502827.8027.607170.8070.503029.8029.600013.0-7271.8071.503231.8031.607574.8074.503433.8033.600016.0-8079.8079.500019.0-(提示的附录)有工艺余量的心轴直径尺寸JB/T9163.10－1999中华人民共和国机械行业标准压帽式剃珩齿心轴尺寸JB/T9163.10－1999*机械工业部机械标准化研究所出版发行机械工业部机械标准化研究所印刷（北京首体南路2号邮编100044）*开本880×12301/16印张X/X字数XXX,XXX19XX年XX月第X版19XX年XX月第X印刷印数1－XXX定价XXX.XX元编号XX－XXX